$59.99 — X20. Hall Effect sticks that pull out and can be replaced for $11.99, a 1,000mAh battery, and 1000Hz polling over wired and 2.4GHz. The better long-term buy if you play on PC.
$79.99 — X20 Pro. TMR sticks with 40–80gf adjustable tension, dual-mode micro-switch triggers, four rumble motors, six programmable buttons, a screen and the same 1000Hz polling. The better buy for competitive FPS, and for Switch or mobile where no PC software exists to configure it with.
The $20 difference buys trigger hardware and a charging dock — not more stick precision. Both sticks are contactless, and neither wears out the way a potentiometer does.
X20 vs X20 Pro at a Glance
| EasySMX X20 | EasySMX X20 Pro | |
|---|---|---|
| Price | $59.99 | $79.99 |
| Sticks | Hall Effect, magnetically removable, height adjustable | TMR, 40–80gf adjustable tension |
| Triggers | Hall Effect, 2-way trigger lock | Hall Effect + micro-switch mode, leaf-spring pre-load |
| Haptics | Dual motors, 5 intensity levels | Quad motors with instant brake |
| Back buttons | 4 fixed (M1–M4) | 2 fixed + 2 hot-swappable, plus 2 mini shoulder buttons |
| D-pad | Fixed | Swappable, 2 spares in the box |
| Display | No | Yes, on-device settings and battery |
| Battery | 1,000mAh | 1,000mAh |
| Weight | 225.8g net | 268g ±5g net |
| Polling rate | 1000Hz wired / 2.4G, 125Hz Bluetooth | 1000Hz wired / 2.4GHz (≤2ms latency) |
| Receiver | Separate 2.4G dongle included | 3-in-1 magnetic receiver, charger and stand |
| Connection | 2.4GHz / Bluetooth / USB-C | 2.4GHz / Bluetooth / USB-C |
| Platforms | PC, Switch, iOS, Android | PC, Switch, iOS, Android |
| Released | August 2024 | September 2026 |
The 30-Second Answer
Buy the X20 if you play on PC, want a controller you can repair yourself, and would rather spend the $20 on games. Its sticks lift out with a magnet and replacements cost $11.99.
Buy the X20 Pro if you play shooters competitively, or if you mostly play on Switch or a phone. Its screen lets you change settings without a PC, and its trigger can switch to a mechanical click.
Buy neither if you only play single-player story games and do not care about back buttons. The X05 Pro and D10 below cover that job for less.
What's Actually Different
Sticks: swappable Hall Effect vs tension-adjustable TMR
Both controllers use magnetic sensing instead of the carbon-film potentiometers that wear out on cheaper pads. That means neither one develops the classic drift caused by a worn resistive track. The difference is what you can do with the stick after it leaves the factory.
The X20's sticks are held on by magnets. Pull one up and it comes off; the height can be changed with the spare set, and a replacement pair costs $11.99. If a stick ever feels loose, gritty or uneven after a few years, you replace one part instead of the whole controller. Given that a controller usually outlives two or three of its own sticks, this is the most practical thing about the X20 and the least talked about.
The X20 Pro uses TMR sensors — the newer tunnel-magnetoresistance design — with a tension ring you turn by hand. The dial travels between 40gf and 80gf, so you can set the stick light for fast camera flicks in a shooter and firm for slow, deliberate aiming in a sniper game. Nothing on the X20 adjusts.
What the Pro does not offer is a user-replaceable stick. Its box includes two spare D-pads, not spare sticks, and the $11.99 magnetic replacement joysticks are sold as an accessory for the X20 only. The two modules do not interchange: the X20 uses a Hall Effect stick in a magnetic socket, while the Pro's TMR sensor sits in a different housing with the 40–80gf tension collar, so the base, magnet layout and sensor footprint do not line up. No replacement stick module is sold for the Pro. So the trade is precise: the X20 gives you a stick you can fix, the X20 Pro gives you a stick you can tune.
Triggers: a lock versus a switch
Both listings call their triggers “dual-mode”, but these are not the same feature with two names, and the difference matters more than any spec on the box.
The X20 has a two-way trigger lock. A slider shortens the trigger's travel and stops it early, which is what you want in a shooter where you need the input to fire fast. The trigger itself is still analog — it still reports a range of values.
The X20 Pro keeps that analog Hall Effect travel for racing games, and adds a micro-switch mode where the trigger behaves like a mouse button: one clean click at a fixed point, identical every time. It also pre-loads the trigger with an internal leaf spring, which removes the small dead gap before the trigger starts registering. For anyone who has lost a fight to a trigger that felt mushy, this is the upgrade. The X20's lock shortens the pull but stays analog — it never becomes a micro-switch.
Haptics: two motors versus four
The X20 runs dual rumble motors with five intensity levels you can cycle through. It is the standard arrangement and it works — the grips buzz, the triggers do not.
The X20 Pro doubles that to four motors and adds a circuit that cuts vibration the instant it ends. In practice the Pro feels more like it is reacting to what is on screen and less like it is humming along underneath the game. Whether that is worth $20 depends on whether you notice haptics at all. Plenty of players turn rumble off entirely, and if you are one of them this whole section is worth nothing to you.
Buttons, D-pad and the screen
The X20 has four fixed back buttons, labelled M1 to M4, programmed through the KeyLinker app on a PC. Two sit low on the grips, two sit closer to the centre. That is a solid macro setup for fighting games and looter shooters, and it needs no software once configured.
The X20 Pro goes further: two fixed back buttons, two more that pull out and can be swapped, plus two extra mini shoulder buttons next to the bumpers. That is six programmable inputs. Its D-pad is also swappable, with two spares in the box, so you can change the shape of the cross to suit fighting games or platformers.
The screen is the part people underestimate. On PC you can run the KeyLinker app and never touch it. On Switch, iOS and Android there is no such app — which is exactly where a small display that changes deadzone, vibration and connection mode becomes the only way to configure the pad at all. If you play handheld, the screen is not a gimmick.
Charging: a dongle versus a dock
The X20 ships with a plain 2.4GHz receiver, and charging is a USB-C cable. Simple, and a spare receiver costs $11.99 if you lose one.
The X20 Pro's receiver is also its charger and its stand. You set the controller down on it and it charges; you pick it up and it reconnects. The receiver has a short cable so you can move it off the back of a desktop PC, where USB ports are usually buried and shielded by a metal case. If your PC sits on the floor, this solves a real problem. If you play on a TV from the sofa, you will still be running a cable to the receiver, so the convenience mostly evaporates.
Hall Effect vs TMR: does it matter here?
Both technologies replace the physical wiper that wears down in a normal analog stick, so both are drift-resistant by design rather than by tuning. Neither one is "more drift-proof" than the other in any way you could measure on a desk.
Where they differ is manufacturing tolerance and feel. Hall Effect sensors read a magnetic field that changes as the stick moves; TMR sensors use a different magnetic effect that produces a cleaner signal with less noise and less power draw. In a controller, that mostly shows up as a stick that centres more precisely and holds a linear response near the edges. It is a real improvement, but a small one, and it is not the reason to spend $20.
If you want to know whether your current controller has a problem, measure it rather than guess: a stick that reports a resting position away from centre is drifting, and no amount of sensor technology talk changes that. We explain what deadzone is and how it affects aim in our deadzone guide.
For the deeper comparison of the two sensor types, we have written about it separately in Hall Effect vs TMR joysticks and what TMR actually fixes.
Build, weight and hand feel
The X20 weighs 225.8g net and measures 15.30 × 10.20 × 5.60cm. EasySMX confirms the X20 Pro controller on its own at 268g ±5g (about 263–273g). The 600.0g and 18.00 × 18.00 × 6.80cm on the product listing are boxed shipping figures: the magnetic charging receiver, cable, two spare D-pads, stand and packaging all ship in the same carton, so do not read 600g as the weight in your hands. At 268g the Pro is roughly 42g — about 19% — heavier than the X20, which you will notice over a long session but which is still normal for a full-size wireless pad with a screen and four motors.
In the hand the X20 is the lighter, flatter of the two, with a fine cross-hatch texture across the grips that stays grippy when your palms are not. The X20 Pro is taller through the body, which pushes the triggers further from your index fingers at rest, and its sticks sit noticeably higher because of the tension collar underneath.
One thing to check before buying either: the X20's back buttons sit close together near the centre of the shell, and players with large hands sometimes brush them during fast play. The Pro moves two of its back buttons out toward the grips and makes them removable, which is a direct answer to that complaint.
Battery and latency
Both controllers use a 1,000mAh battery and the same Type-C port. Neither advertises a play-time figure in hours, and we would not repeat a number we have not measured ourselves.
Polling is not a reason to choose between them: both controllers run at 1000Hz over USB-C and 2.4GHz in XInput mode, and both are stable in those two modes. The X20 Pro is the one with a published end-to-end latency target — under 2ms in wired and 2.4GHz use — while the X20's published figure is a polling rate. The X20 drops to 125Hz over Bluetooth; on Bluetooth, the connection is the bottleneck rather than the controller.
What we can say is that 1000Hz matters less than it sounds. Going from 125Hz to 1000Hz reduces the worst-case input delay from about 8ms to about 1ms; past 500Hz the difference is below what a human can perceive in a game. If you play wired or on 2.4GHz, either controller is already fast enough, and no model choice will make a measurable difference in a firefight.
Full specification comparison
| Specification | X20 | X20 Pro |
|---|---|---|
| Model number | VG-C518 | VG-C478 (Grey) / VG-C479 (Black) |
| Colour | White | Grey, Black |
| Stick sensor | Hall Effect | TMR |
| Stick tension | Fixed | 40–80gf adjustable |
| User-replaceable sticks | Yes, magnetic, spares $11.99 | No separate module sold; X20 sticks do not fit |
| Trigger | Hall Effect, 2-way lock | Hall Effect + micro-switch, leaf-spring pre-load |
| Rumble motors | 2, five intensity levels | 4, instant brake |
| Programmable inputs | 4 back buttons | 6 (2 fixed + 2 hot-swap + 2 mini shoulder) |
| Display | None | Smart display |
| Battery | 1,000mAh | 1,000mAh |
| Polling rate | 1000Hz wired / 2.4GHz, 125Hz Bluetooth | 1000Hz wired / 2.4GHz (≤2ms latency); Bluetooth not stated |
| Charging port | USB-C | USB-C + magnetic dock |
| Connectivity | 2.4GHz, Bluetooth, wired | 2.4GHz, Bluetooth, wired |
| Platforms | Windows 7–11, Switch, iOS, Android | Windows, Switch, iOS, Android |
| Weight | 225.8g net | 268g ±5g net |
| In the box | Controller, USB cable, 2.4G receiver, manual | Controller, magnetic receiver, 2 spare D-pads, USB cable, stand, manual |
| Warranty | 18 months | 18 months |
Which one should you buy?
Competitive shooters — Valorant, CS2, Apex Legends. Take the X20 Pro. The micro-switch trigger gives you the same actuation point every single press, which is what separates a consistent peek from a lucky one, and the tension ring lets you firm up the right stick for tracking without making the left stick sluggish. The four motors and instant brake also make directional damage cues easier to place. This is the setup the Pro was built for.
PC single-player and long sessions — Elden Ring, Cyberpunk, Baldur's Gate 3. Take the X20. These games do not reward a 1ms trigger, and they do reward a controller that still works in three years. When the stick eventually loosens, $11.99 and thirty seconds of your time fixes it. You also save $20, which is most of a new game.
Switch, iPhone or Android. Take the X20 Pro, and this is the strongest case for it. There is no KeyLinker app on Switch or iOS. On the X20 you set deadzone, macros and vibration on a PC and then hope the settings travel with the controller. On the Pro you change them on the screen, in the middle of a session, without leaving the game. If you play handheld more than docked, that is not a convenience — it is the difference between being able to configure the pad at all.
Desktop PC, clean setup, hates hunting for cables. Take the X20 Pro for the dock. The receiver plugs into the stand, the controller drops onto it, and the whole thing sits on your desk instead of dangling off the back of the tower. If your PC is on the floor with rear ports against a wall, this is worth more than any spec on this page.
Who should not buy the X20 Pro
If you already own an X20 and it works, do not upgrade for the sticks. The TMR sensors are better, but they are not $79.99 better, and your Hall Effect sticks are not going to wear out the way a cheap pad's would. Upgrade only if you specifically want the micro-switch trigger, the screen, or the dock.
If you only play on PC and already own a 2.4GHz receiver you are happy with, a third of the Pro's price is going into a charging stand you did not ask for.
If you do not use back buttons, six programmable inputs are a liability, not a feature. Extra buttons near where your fingers rest get pressed by accident, and you will spend a week retraining your grip around them.
And if you play on PlayStation or Xbox, neither controller is for you. Both list PC, Switch, iOS and Android only. No amount of firmware will add console support.
Where the X20 fits in the rest of the lineup
The X20 is the middle of the Hall Effect line: below it sit the X05 Pro and D05, which keep the Hall sticks and drop the screen and extra buttons; above it now sits the X20 Pro. If you want TMR without the Pro price, the D10 pairs TMR sticks with a trigger lock and a charging dock, and the S10 and S05 Pro cover the same sensor generation in different shells.
Whichever you pick, budget for one extra thing: the X20's sticks are its best feature and its most likely loss. A spare pair is $11.99, and losing a stick is the single most common way these controllers stop being usable.
Frequently asked questions
Can the X20 Pro use the X20's magnetic replacement sticks?
No. The X20's replacement joysticks are sold as a separate accessory listed specifically for the X20, and the two modules are not interchangeable. The X20 uses a Hall Effect stick in a magnetic socket; the X20 Pro uses a TMR sensor inside a different housing with the 40–80gf tension collar, so the base, magnet layout and sensor footprint do not line up. The Pro ships with two spare D-pads, not spare sticks, and no replacement stick module is sold for it. If being able to repair a stick yourself is why you are buying, that is the X20's advantage, not the Pro's.
Do Hall Effect and TMR sticks ever drift?
Not from wear. Both read a magnetic field without physical contact, so there is no resistive track to erode. Drift can still come from a loose stick housing, a firmware calibration error or a damaged sensor, but the slow creep that kills potentiometer sticks does not apply.
Does the X20 Pro work on PS5 or Xbox?
No. Neither the X20 nor the X20 Pro lists PlayStation or Xbox compatibility. They support Windows, Switch, iOS and Android over 2.4GHz, Bluetooth or USB-C.
Can I use the X20 Pro wired without the receiver?
Yes. It connects over USB-C as a wired controller, and the receiver is only needed for 2.4GHz wireless. The dock is a convenience, not a requirement.
Does the X20 Pro screen work when connected to Switch?
Yes — that is the point of it. Settings are stored on the controller itself, so the display works regardless of what it is plugged into, including platforms with no companion app.
Is the X20 Pro worth $20 more than the X20?
Only if you will use what the $20 buys: a micro-switch trigger, a tension ring, four motors, two extra programmable inputs, a screen, and a charging dock. If you mainly play single-player games on PC, the X20 does the same job and its sticks are cheaper to replace.
Which X20 model has lower latency?
Neither, in any way you would feel. Both run at 1000Hz over USB-C and 2.4GHz, and the X20 Pro is quoted at under 2ms end-to-end latency in those two modes. The X20 drops to 125Hz over Bluetooth. In practice the connection you choose matters far more than the model: wired or 2.4GHz on either controller is faster than Bluetooth on either.
Do both controllers support 1000Hz polling?
Yes. Both the X20 and the X20 Pro run at 1000Hz over USB-C and 2.4GHz in XInput mode. The Pro is additionally quoted at under 2ms latency in those modes. Bluetooth is the slower connection on both; the X20 drops to 125Hz there.
اترك تعليقًا