You can customize the screen wallpaper on your EasySMX X20 Pro by following these steps:

1. Power off the controller.

2. Press and hold the M button, then connect the controller to your PC using a USB cable.

3. The LED will turn white, indicating that the controller has entered upgrade mode.

4. Unzip the wallpaper folder and open the Wallpaper Tool on your PC.

5. Load your preferred image and crop it to the required size of 160 × 80 pixels. JPG, PNG, and GIF formats are supported.

6. Check the preview and click Burn. Wait until the process is complete.

7. Disconnect the USB cable and power on the controller.

Your custom wallpaper will now appear on the controller's screen.

Note: Please make sure the image is cropped to 160 × 80 pixels before burning it to the controller.

Wallpaper Tool: [Download Wallpaper Tool]

If your joysticks, triggers, or motion sensor are not working properly, you can calibrate your EasySMX X20 Pro through the on-screen menu.

1. Long-press the HOME button for 3 seconds to enter the on-screen menu.

2. Select Calibration and press A to confirm.

3. Follow the on-screen instructions to calibrate the joysticks, triggers, and motion sensor one by one.

Tips:

a. Place the controller flat on a stable desk before calibration.

b. Do not touch or move the joysticks during the calibration process.

c. Follow the on-screen prompts to complete each calibration step.

You can adjust the vibration intensity directly through the controller's on-screen menu.

1. Long-press the HOME button for 3 seconds to enter the on-screen menu.

2. Select Vibration and press A to confirm.

3. Move the left joystick to adjust the vibration intensity.

4. Press A to save your settings.

The EasySMX X20 Pro allows you to customize its lighting effects and screen brightness.

1. Long-press the HOME button for 3 seconds to enter the on-screen menu.

2. Select RGB and press A to confirm.

3. You can adjust the following settings:

    Screen brightness

    RGB brightness

    RGB color

    RGB lighting mode

Note: The screen brightness cannot be turned off. However, RGB lighting can be completely disabled by setting the RGB brightness to zero.

The on-screen menu allows you to customize various controller settings.

1. Slide the power switch to the ON position.

2. Long-press the HOME button for 3 seconds to enter the menu.

3. Use the left joystick to move up, down, left, or right to navigate.

4. Press A to select or confirm.

5. Press B to go back.

Tip: When the controller is asleep, briefly press the HOME button to wake it up.

The EasySMX X20 Pro supports two joystick gate modes: Circular and Square.

1. Press and hold M + START simultaneously for 2 seconds to switch between the two modes.

2. The controller will vibrate to confirm that the mode has changed.

Circular Mode: Provides a rounder joystick movement range, making it suitable for fighting and racing games.

Square Mode: The default setting, offering a joystick movement range suitable for most games.

The EasySMX X20 Pro supports two trigger vibration modes.

1. Press M + BACK to cycle between the trigger vibration modes.

2. The available modes are:

    Native Vibration: Works only via Bluetooth and requires support from the game itself.

    Follow-Motor Vibration: Uses the controller's motor vibration to simulate trigger feedback.

Note: Native Vibration requires both a Bluetooth connection and game compatibility. If the game does not support Native Vibration, please switch to Follow-Motor Vibration.

The EasySMX X20 Pro supports mapping gyroscope input to either joystick.

Note: This function is only available in Xinput mode.

1. Make sure the controller is in Xinput mode.

2. To map the gyroscope to the left joystick, press and hold START while pressing down the left joystick (L3) simultaneously.

3. To map the gyroscope to the right joystick, press and hold START while pressing down the right joystick (R3) simultaneously.

4. The controller will vibrate to confirm that the setting has changed.

You can record custom button combinations on the programmable back buttons (M1–M6). 

Using M1 as an example:

1. Press M + M1 simultaneously. The LED will flash white, indicating that the controller has entered programming mode.

2. Press the button sequence you want to record.

3. Press M1 once to save the macro. The RGB light will flash to confirm that the macro has been saved.

4. Repeat the same steps to program M2, M3, M4, M5, or M6.

How to Clear a Macro:

1. Press and hold M + M1 simultaneously.

2. Press M1 once again to clear the recorded macro.

3. Repeat the same procedure for the other programmable back buttons.

The EasySMX X20 Pro supports three Turbo states: Manual Turbo, Auto Turbo, and Off.

How to Enable or Disable Turbo:

1. Press M + the target button to cycle through the Turbo settings.

2. Each press switches between the following three states:

    Manual Turbo: The button triggers continuous input while being held down.

    Auto Turbo: Press the button once to activate continuous input automatically.

    Off: Disables the Turbo function.

3. The controller will vibrate to confirm the change.

How to Adjust Turbo Speed:

Press M + push the right joystick upward to increase the Turbo speed.

Press M + push the right joystick downward to decrease the Turbo speed.

Supported Buttons: A, B, X, Y, LB, RB, LT, RT, D-pad, and M1–M6.

Note: The back buttons (M1–M6) support Auto Turbo only.

The EasySMX X20 Pro supports both Xinput and Dinput modes.

1. Press and hold BACK + START simultaneously for 3 seconds.

2. The controller will switch between Xinput and Dinput modes.

3. When connected to a PC in Dinput mode, the device name will appear as EasySMX X20 Pro.

Recommendation: We recommend using Xinput mode for everyday gaming, as most PC games recognize this mode. Dinput mode is available for games that specifically require it.

The EasySMX X20 Pro supports three connection methods:

1. 2.4G Wireless Connection

Plug the included 3-in-1 receiver into your PC or compatible device. The controller will connect wirelessly through the receiver.

2. Bluetooth Connection

Switch the controller to Bluetooth mode and search for the device on your device's Bluetooth settings.

The controller will appear as Xbox Wireless Controller.

3. Wired Connection

Connect the controller directly to your device using a USB cable.

Note: In Dinput mode, the device name appears as EasySMX X20 Pro. Please refer to the actual device name displayed on your device when pairing.

Follow these steps to pair your EasySMX X20 Pro with a Nintendo Switch:

1. Long-press the HOME button for 3 seconds to enter the on-screen menu.

2. Select Mode, then choose Switch and press A to confirm.

3. On your Nintendo Switch, navigate to Controllers → Change Grip/Order.

4. Stay on this screen and wait a few seconds for the controller to connect automatically.

Important: Do not leave the Change Grip/Order screen until the controller has successfully connected.

The LED indicator displays different charging statuses depending on the controller's operating state.

1. Charging While Connected (Wired or Wireless)

    The LED indicator for the current mode breathes while charging.

    The LED indicator stays solid when the controller is fully charged.

2. Charging While Asleep or Powered Off

    The LED indicator breathes red while charging.

    The LED turns off once the controller is fully charged.

3. Charging with the Dock

Simply place the controller on the charging dock to start charging automatically.

Note: The controller can also be charged directly through its USB-C port.

Here are the battery specifications of the EasySMX X20 Pro:

a. Battery Capacity: 1000 mAh

b. Input: 5V

c. Charging Time: Approximately 2–3 hours

d. Battery Life: Approximately 8–10 hours under normal use

e. Low Battery Alert: The LED flashes red rapidly when the battery level drops below 20%.

Actual battery life may vary depending on usage, lighting, vibration intensity, and connection method.