a.Button Function Calibration

1. Under the power-on condition, press the ‘X “, ”-’ & ‘+’ buttons at the same time, the indicator lights 1 &2 flash alternately.

2. Turn the left and right joysticks clockwise three times at a constant speed, and press the left and right triggers three times at a constant speed. 

3. Finally press ‘+’ button to exit

b.Joystick and Gyroscope

1. While controller is powered on, press and hold the “+”, “-”, and “B” buttons for 3 seconds to enter calibration mode.

2. Rotate the left and right joysticks two full turns each, then place the controller horizontally for 3 seconds. Press the B button briefly to exit calibration mode.

In this mode, you can simultaneously calibrate both the joysticks and the gyroscope.

Click here to watch calibration tutorial

1. Click on the upgrade package in the attachment,

2.Turn off the controller,then press and hold L3 ,using the data cable to connect to the controller on the PC, 

3.When upgrade package recognise successfully, click it and wait it.

a.Connect to Phone/Tablet/PC via Bluetooth

1. On the back of the controller, switch the controller to the ' X ' position.

2. Press and hold Home for 3 seconds. The indicator light will flash to enter pairing mode.

3. Click ‘Xbox Wireless Controller’ on the Bluetooth interface to pair. When the connection is successful, the indicator light will remain with short vibration.

Note: If the first pairing is unsuccessful, delete the pairing information on your mobile phone and repeat the operation.

b.Connect to Switch 2

1. Set the switch on the back of the controller to the ‘S’ position. 

2. Hold the HOME button for 3 seconds until the LED starts flashing rapidly.

3. On the Switch console, navigate to [Controllers] > [Change Grip/ Order]; when the LED turns solid and a short vibration occurs,

within 20 seconds after pairing, remove the Joy-Con controllers from the console and reattach them——this action activates the wireless 

wake-up function (only required during first-time connection)

c.Connect to Switch 1

1. Slide the Mode Toggle to the""S"" mode.

2. Press and hold the Home button for 5 seconds to power on.

3. The controller's LED willflash (indicating pairing).

4. On the Switch, navigate to Controllers > Change Grip/Order to enter

pairing mode.

5. When the LED becomes steady with a short vibration to confirm pairing.

Reconnection:

Keep the Mode Toggle under ""S"" mode, and short-press the Home button

to reconnect your Switch.

d.Wired Connection to Switch

e.Connect to PC via Bluetooth in Switch Mode

a.Set

1. With the controller connected, press and hold M and GL/GR buttons. The RGB light will flash red, indicating that you have entered programming mode.

2. Press the button you want to program (e.g. A or A and B).

3. Finally, press the GL/GR buttons once to save. The RGB light will return to its current state, indicating that programming was successful.

b.Forbidden

When the controller is connected, press the M button & GL/GR to enable Macro programming mode. The indicator light will flash red, 

indicating that programming mode has been entered. Press the GL/GR button once to disable it.

a.Lighting Mode:

Double-click the M button, and the controller will vibrate briefly to enter RGB adjustment mode. Use the left joystick up or down to switch between lighting modes.

Mode 1: Dynamic

Mode 2: Breathing (Turn the left stick left or right to circle colors)

Mode 3: Constant On (Turn the left stick left or right to circle colors)

Mode 4: Gradient

Mode 5: Off

b.Brightness Adjustment:

In RGB adjustment mode, press the left joystick down to cycle through RGB light brightness levels. Adjustable from 1 to 4 levels.

Sleep mode: The indicator light flashes red slowly when charging, and the green light stays on when fully charged.

Connection status: The current mode light stays on.

【Note】When the controller is connected, the indicator light flashes red quickly to indicate low battery. Please charge it in time.

While connected, press and hold the “+”, “-” and “HOME” buttons for 5 seconds.

1 x EasySMX S10 gamepad

2 x Magnetic Faceplates

1 x Detachable Circular D-Pad

1 x Detachable Cross-shaped D-Pad

1 x Type-C Data Cable

2 x DIY Stickers

1 x Instruction manual