Free browser tool · No download

Gamepad Tester

This free gamepad tester connects to any Xbox, PlayStation, Switch or PC controller and checks every button, trigger and analog stick in real time. The built-in drift scan measures your sticks while you let go — so you can see wear that your hands can feel but your eyes cannot.

Press any button on your controller, or click here, to start
Status Waiting
Mapping —
Browser read rate —
Buttons seen 0 / 17

Left stick

Raw axes 0 / 1

X 0.00Y 0.00

Buttons & triggers

No controller detected

LT / L20%
RT / R20%
Coverage0 of 17 buttons

Right stick

Raw axes 2 / 3

X 0.00Y 0.00

Stick drift scan

Put the controller down on a flat surface and do not touch the sticks. For 8 seconds the tool records every sample your controller reports with nobody touching it. A healthy stick returns to dead centre; a worn one keeps reporting a small offset, which most games translate into camera creep or "walking" characters.

Result
Not scanned yet

Connect a controller, rotate both sticks once to wake them up, then let go and run the scan.

Left stick offset—
Right stick offset—
Jitter (sample noise)—
Suggested deadzone—

Offsets are reported as a fraction of full stick travel. Most games ship a deadzone between 0.10 and 0.25, which is why light drift hides in menus and shows up as camera creep in shooters.

Circularity test

Drift and circularity are different problems. The drift scan measures where a stick rests when you let go. This test measures how far it can actually travel in every direction: hold a stick against the outer edge and turn it slowly through one full circle, then do the same for the other stick. The outline below is built from the largest radius recorded in each of 32 directions and compared with the ideal circle of radius 1.00.

Result
Not tested yet

Connect a controller and press any button first. Then start the test and rotate both sticks slowly along the outer edge.

Directions covered0 / 32
Average radius—
Circularity error—
Over-range—

A square or octagonal gate, a firmware mapping or a worn shaft can all keep a stick from reaching the same radius in every direction. This measures the outer range, not wear-induced drift — a Hall Effect or TMR stick can still show an uneven outline.

If your sticks are drifting, you have three ways out

Shown for everyone — the scan narrows it down

How to use this gamepad tester

  1. Connect the controller. Plug it in by USB or pair it over Bluetooth, then press any button. Browsers only expose a gamepad after a real button press — this is a security rule, not a bug in the tool.
  2. Press every button once. The grid lights each input as it registers, so you can find a dead face button, a mushy bumper or a trigger that never reaches 100%.
  3. Let go and run the drift scan. Place the controller down, hands off, and start the 8-second scan. You get a plot of the resting position plus a verdict, and a deadzone value you can enter in Steam, emulators or in-game settings.
  4. Check the outer range. Sweep each trigger slowly from 0 to 100% and watch for jumps, flat spots or a value that never reaches full travel. Then run the circularity test: hold each stick at the edge and turn it through a full circle to see whether every direction reaches the same radius.
What this tool cannot do: a browser can read your controller but it cannot write to it. That means there is no true "calibration" here — no firmware recalibration, no stick re-centring. What you get is a measurement, a deadzone recommendation and a hardware verdict. Anything that claims to recalibrate a controller from a web page is either rebinding software or guessing. The Gamepad API also cannot see gyroscopes, battery level, firmware version, connection mode, which app owns the controller, or adaptive-trigger resistance — it reports buttons and axes only.

What the drift scan actually measures

When you release a stick, the springs should pull it back to the exact centre, and the sensor should report 0.00, 0.00. Worn hardware does not quite do that. Over 8 seconds the scan collects several hundred samples and derives three numbers:

MetricWhat it meansHealthy range
OffsetDistance between the average resting position and true centre. This is the number that causes camera creep.Under 0.03
JitterHow much the reading bounces between samples with nobody touching the stick. High jitter points at a noisy sensor or a loose connection.Under 0.02
95th percentile radiusHow far the stick wanders at its worst 5% of moments. Drift is not constant, so this catches the spikes an average hides.Under 0.055

We use the 95th percentile rather than the maximum because a single electrical spike can be a cable artefact. If the worst 5% of samples still sit well inside your game's deadzone, you will never feel the problem.

Why analog sticks drift in the first place

Potentiometer sticks wear out — this is mechanical, not software

A conventional analog stick — the joystick under your thumb — sits on two potentiometers: resistive carbon tracks with a wiper that slides across them as you move. Every hour of play scrapes the wiper along the track. Carbon abrades, the contact resistance changes, and the voltage the controller reports no longer matches the physical centre. This is why drift appears gradually, why it usually hits the left stick first (movement stick, most travel), and why no amount of cleaning fixes it permanently. The track is physically gone.

Hall Effect sticks remove the wear surface

A Hall Effect stick replaces the resistive track with a magnet on the stick shaft and a Hall sensor on the PCB. The sensor reads magnetic field strength, so nothing rubs against anything and the sensing element never wears. There is no carbon to abrade, which is why Hall Effect sticks are marketed as drift-free.

The honest caveat: a Hall Effect stick can still report a small offset. Springs fatigue, the shaft can develop play, and the factory centre point can shift if the magnet moves. So "drift-free" means no wear-induced drift, not "will read exactly 0.00 forever". Run the scan and you will typically see an offset near zero but a non-zero jitter figure — that is normal sensor noise, not a defect.

TMR is the newer, more sensitive version of the same idea

Tunnel Magnetoresistance sensors use a magnetic tunnel junction instead of a Hall plate. The practical differences are higher sensitivity at small field changes, lower power draw, and better linearity near the centre — which is exactly the region where drift lives. In stick terms, a TMR stick resolves small movements more finely and holds its centre more consistently over long sessions.

Hall Effect vs TMR: which one should you buy

PotentiometerHall EffectTMR
Wear-induced driftYes, inevitableNoNo
Centre resolutionCoarse, degradesGoodBest
Power drawLowModerateLow
Typical useBudget padsMainstream pro pads2025+ flagship pads

If your current pad already drifts, the decision is not really Hall vs TMR — it is repair vs replace. Both non-contact designs solve the same root cause; TMR simply gives you more headroom at the centre for competitive aiming.

Fixing drift: what actually works, in order

  1. Raise your deadzone. Free, instant, and hides the symptom. Use the suggested value from the scan, then add 0.01. This buys you months, not years.
  2. Replace the stick module. If your controller uses swappable magnetic modules, this is a two-minute job and much cheaper than a new pad. Test again afterwards — the offset should drop below 0.03.
  3. Clean the stick base. Compressed air around the shaft can clear grit that adds mechanical resistance. It will not restore worn carbon, so treat it as a diagnostic step.
  4. Replace the controller with a non-contact stick design. The permanent fix, and the only one that stops the clock.

Frequently asked questions

Is this gamepad tester free to use?

Yes. The tool is free, needs no account and no download, and runs entirely in your browser. Nothing you press, move or scan is uploaded, so you can test a controller you are about to buy or return without installing anything.

Does this gamepad tester work on iPhone and iPad?

Yes, on iOS 16.4 or later. Safari on iPhone and iPad exposes the Gamepad API, so buttons, sticks and the drift scan all work with a Bluetooth controller. Press one button first so the browser exposes the pad. Vibration is the only check that stays unavailable, because Safari does not support the vibration actuator. Older iOS versions and in-app browsers may still fail to detect a controller.

Why does nothing happen until I press a button?

The Gamepad API deliberately hides controllers until a real user input occurs, so a page cannot silently fingerprint the devices plugged into your machine. Press any face button or move a stick once and the browser will hand the gamepad to the page.

My controller shows up but the buttons are in the wrong place.

That means the controller is not reporting the standard mapping. Some pads in DirectInput or Switch mode enumerate with a different order. Switch the pad to XInput or PC mode using its mode switch or button combo, then reconnect. The mapping chip in the status bar will read standard when it is correct.

Is a small offset on a brand new controller normal?

Yes, up to about 0.02. Manufacturing tolerances and spring settling both contribute. Anything under 0.03 is inside the noise floor of most game engines and will not be felt. A new controller reporting 0.08 or more is worth returning.

Can I calibrate my controller here?

No. A browser has read-only access to gamepads. You can measure the offset, and you can change the deadzone in Steam, in an emulator or in game settings, but the controller's own firmware cannot be recalibrated from a web page.

Does the scan send my data anywhere?

No. Buttons, axes, device name and scan samples are read from the browser, computed here and kept in memory only — nothing is uploaded and nothing is written to storage. The only requests this page makes are for its own static assets, including the product thumbnails in the recommendation cards. Some online testers collect device identifiers into a public dataset — this one deliberately does not.

What does "Browser read rate" mean?

It is how often this page can read the controller, not the controller's polling rate. Browsers sample the Gamepad API in step with the display refresh (typically 60, 120 or 144 Hz), so a 1000 Hz wired controller still reads around 60 Hz here. Use it as a connection-consistency check, never as a hardware specification.

What is circularity, and how is it different from drift?

Drift is where a stick rests when you let go. Circularity is how far the stick can travel in each of 32 directions when you hold it at the outer edge. An uneven outline usually comes from a square or octagonal gate, a firmware mapping or a damaged shaft — not from sensor wear. A Hall Effect or TMR stick can still have an uneven outline.

What can't a browser test?

Gyroscope and accelerometer aiming, battery level, firmware version, connection mode, which app currently owns the controller, and adaptive-trigger resistance are all invisible to the Gamepad API. It reports only buttons and axes. Motion and trigger-resistance checks belong in the console's own settings or a native app.

My controller is connected but the page sees nothing.

Check in order: use a data-capable USB cable (many charge-only cables carry power but no data); plug into a rear motherboard port rather than an unpowered hub; close Steam or any app using exclusive controller mode; keep this tab focused in the foreground; press a button on the pad; then refresh the page. On Windows, Chrome and Edge give the most complete results — Firefox does not support vibration, and Safari needs 16.4 or later.