1. Double-click the upgrade file to open the upgrade tool.

2. Press and hold the Left Stick button(L3) and keep it held down.

3. While holding L3, connect the controller to your PC via USB cable.

4. Click ""Upgrade"" in the software interface. Wait for the progress bar to complete (do not disconnect during this process).

5. Once upgraded, power on the controller. Hold the C button for 5 seconds to restore factory settings (LED will blink to confirm).

Manual turbo：Press T+A for the first time； Hold down the A button for continuous trigger of A button

Automatic TURBO：Press T+A for the second time; Press the A button once for automatic continuous firing.

Disable TURBO: Press T+A for the third time

【Note1] C button+pushing up the left joystick increases the rapid fire speed;

C button+pushing down the left joystick decreases the rapid fire speed.

【Note2] NS gear position: Cbutton+function button,set the rapid fire.function for all buttons.

Please poke the reset button at the back of the controller to restart the controller.

a.When connecting to the device

The LED light is always on when it is full, for example, when wired to a computer for charging or charging in use, LED 1&LED 2 flashes to indicate that it is charging, and LED 1&LED 2 is constant to indicate fully charged.

b.When not connected to a device

Such as directly connected to the charger, the four LEDs are blinking at this time, and go out when full.

*Note: 

LED light at the bottom of X20, can't check the battery percentage function. 

When connected wirelessly, a rapidly flashing indicator light at the bottom indicates low battery level.

1. Make sure the M buttons on the back are functioning properly. Press and hold C + M1/M2/M3/M4 until the grip indicator lights flash to enter programming mode.

2. Download KeyLinker from the app store.Connect the controller to your PC via USB cable, open the app, and connect to the device named Xpert2. Go to Settings, tap the menu in the top-right corner, and select Factory Reset. Then you can reprogram the M buttons.

3. Record macros in the Macro settings within the app.

1. While connected, press and hold C + L3 to adjust RGB brightness cyclically through 4 levels: 0 → 1 → 2 → 3.  

2. At level 0, the RGB lights are turned off.

3. To turn ABXY lights on/off:  Press Menu + D‑pad Right to toggle them cyclically.

*The logo light cannot be turned off

1. Forced Motion Sensing Mode

Press and hold C + BACK + Left Stick (pressed down) simultaneously: The left stick will be mapped to the gyroscope function.

Press and hold C + BACK + Right Stick (pressed down) simultaneously: The right stick will be mapped to the gyroscope function.

2. Switch Mode (Wired & Bluetooth Connection)

The gyroscope of X20 can be recognized by Steam when the device is in Switch Mode. 

If the gyroscope still fails to work in games, please first check whether the game itself supports gyroscope functionality. For games on Steam, you can follow these steps to set up and verify the gyroscope:

Open your Steam client and go to your Game Library.

Locate the game for which you want to configure the gyroscope and click on it to enter the game's homepage.

On the far right side of the game's homepage, find the small controller icon and click on it.

Select the option to Edit Layout from the menu that pops up.

Within the ""Edit Layout"" interface, you can view the specific usage instructions and settings related to the gyroscope.

Connection method: 2.4Ghz Wireless, Bluetooth, Wired

Compatible Models: Switch/Switch Lite/Switch OLED, Windows 7/8/8.1/10/11, Android/iOS

Charging Interface: Type C

Battery: 1000 mah

Net Weight: 225.8g

Size: 15.30×10.20×5.60 cm

While the controller is powered on and connected (in any mode), press and hold the C button for 5 seconds.

The controller will vibrate every 0.5 seconds as a prompt, indicating the factory reset was successful.

You may also perform this operation via the Keylinker APP.

1 x EasySMX X20 gamepad

1 x USB data cable

1 x 2.4G receiver

1 x Instruction manual